钼尾矿制备高品质硅钙钾镁肥工艺

    Research on the Process of Preparing High-quality Silicon Calcium Potassium Magnesium Fertilizer from Molybdenum Tailings

    • 摘要: 【目的】为实现尾矿中营养元素富集,同时进一步降低重金属元素,实现尾矿大宗化利用。以河北某钼尾矿为对象,开展了制备高品质硅钙钾镁肥的工艺研究。【方法】首先,钼尾矿进行两次浮选,分别脱除尾矿中的重金属矿物和石英,得到高钾钼尾渣。其次,高钾钼尾渣与石灰石、白云石、石膏按质量比1.0∶0.6∶0.1∶0.2复配后,在1 200 ℃条件下煅烧120 min,此过程中钾长石发生矿相重构使不溶态的钾活化成可溶态的有效钾,制备出硅钙钾镁肥;同时部分重金属及钾会随高温烟气逸出。随后,采用稀酸吸收液吸收烟气,并采用氢氧化钙与磷酸钾共沉淀剂将烟气吸收液中重金属进行沉淀分离,通过蒸发结晶制得高纯钾盐。最后,将煅烧肥料与提取自烟气的钾盐混合后进行研磨,制备得到高品质硅钙钾镁肥。【结果】该肥料全部指标满足国标《硅钙钾镁肥》(GB/T 36207-2018)中I型标准要求,其中有效K2O、Ca、Mg和Si的含量分别超出国家标准I型指标要求含量的70.3%、23.75%、28%和63.11%,且重金属含量远低于标准要求。【结论】本工艺技术为钼尾矿的大宗化、高值化利用提供了新思路,也有助于复合钾肥产业发展。

       

      Abstract: Objective To achieve the enrichment of nutrients in tailings and further reduce heavy metal elements, and to realize the large-scale utilization of tailings. Taking a certain molybdenum tailings in Hebei Province as the object, the process research for preparing high-quality silicon-calcium-potassium-magnesium fertilizer was carried out. Method Firstly, the molybdenum tailings were subjected to two rounds of flotation to eliminate heavy metal minerals and quartz, resulting in high-potassium molybdenum tailings. Subsequently, the high-potassium molybdenum tailing slag was mixed with limestone, dolomite, and gypsum at a mass ratio of 1∶0.6∶1∶0.2 and calcined at 1 200 ℃ for 120 min. During this process, mineral phase reconstruction occurred in potassium feldspar to activate insoluble potassium into soluble effective potassium, thereby producing Si-Ca-K-Mg fertilizer. Simultaneously, some heavy metals and potassium would escape with the high-temperature flue gas. Subsequently, the flue gas was absorbed using a dilute acid absorption solution, and the heavy metals present in the flue gas were precipitated and separated through coprecipitation with calcium hydroxide and potassium phosphate as co-precipitating agents. The resulting high-purity potassium salt was obtained via evaporation and crystallization. Finally, a superior quality silica-calcium-potassium-magnesium fertilizer was prepared by blending calcined fertilizer with potassium salt extracted from the flue gas followed by grinding. Result All parameters of the fertilizer comply with Type I standards outlined in the national standard 'silicon calcium potassium magnesium Fertilizer' (GB/T 36207-2018), wherein the effective K2O content surpasses 70.3% of type I specifications while heavy metal content remains significantly below regulatory limits. Conclusion This innovative technology presents a novel approach for large-scale utilization of molybdenum tailings while also contributing to advancements in the composite potash fertilizer industry.

       

    /

    返回文章
    返回